With an E Release Firmware upgrade, your radios will:

• Send and receive signals with greater reliability.
• Get more than double the range of legacy firmware for remote camera(s) and/or off-camera flash(es).
• Pair your PocketWizards with the revolutionary Raven from Fusion TLC.
• Use Quad Zone Triggering available with all 32 Channels, instead of just 16.
• All use the same, single Channel system.

PLEASE READ IMPORTANT NOTES BELOW AND CHECK THE
CAMERA COMPATIBILITY CHART BEFORE PURCHASING E RELEASE FIRMWARE.

• CANON RADIOS CAN ONLY BE USED AS RECEIVERS WITH THE E RELEASE. You must use a different radio as a transmitter. For TTL, you can use a Raven from Fusion TLC with your PocketWizards as receivers. For manual triggering, you can use a Plus IIIe or Plus IVe as the transmitting radio.
• When you upgrade a PocketWizard radio to the E Release, it uses a different frequency and can only communicate with other radios that have also been upgraded to the E Release.
• You will need at least 2 radios with E Release Firmware. Each radio requires its own firmware license.
• The E Release upgrade is not available for the MiniTT1.
• This license is for an FCC frequency (North, Central, or South America) Transceiver. If your radio says “CE” on the label, please purchase a CE license instead.

Important License Information:

• Please make sure you enter your email address correctly at checkout. The license(s) will be assigned to that email address.
• After purchase, you will receive a confirmation email from “PocketWizard Shop” with further instructions. Note: it may take up to 24 hours for the license(s) to be available.  If you are purchasing physical products in addition to the licenses, the licenses will not be available until the products are shipped.
• The upgrade is completed through the PocketWizard Utility via a USB connection with a computer, either a PC or Mac. It cannot be done on a smartphone or tablet.
• You will need a mini B to USB data cable for the upgrade.
• Installing E Release Firmware requires an active internet connection.
• An upgrade must be purchased for each radio and will be assigned to the radio’s serial number upon installation. Once assigned, it is non-transferable.
• E Release enabled (licensed) radios can be up/down-graded between E Release and Legacy Firmware at any time.

The post FlexTT6-Canon E Release (Receive ONLY) Firmware License (FCC-US/Canada) appeared first on PocketWizard.

The E Release is an easy and inexpensive upgrade that dramatically extends the range, enhances reliability, and expands the features of your existing PocketWizard radios.

With an E Release Firmware upgrade, your radios will:

• Send and receive signals with greater reliability.
• Get more than double the range of legacy firmware for remote camera(s) and/or off-camera flash(es).
• Pair your PocketWizards with the revolutionary Raven from Fusion TLC.
• Use Quad Zone Triggering available with all 32 Channels, instead of just 16.
• All use the same, single Channel system.

PLEASE CHECK THE CAMERA COMPATIBILITY CHART AND SEE IMPORTANT NOTES BELOW BEFORE MAKING A PURCHASE.

• CANON RADIOS CAN ONLY BE USED AS RECEIVERS WITH THE E RELEASE. You must use a different radio as a transmitter. For TTL, you can use a Raven from Fusion TLC with your PocketWizards as receivers. For manual triggering, you can use a Plus IIIe or Plus IVe as the transmitting radio.
• When you upgrade a PocketWizard radio to the E Release, it uses a different frequency and can only communicate with other radios that have also been upgraded to the E Release.
• You will need at least 2 radios with E Release Firmware. Each radio requires its own firmware license.
• The E Release upgrade is not available for the MiniTT1.
• This license is for an FCC frequency (North, Central, or South America) Transceiver. If your radio says “CE” on the label, please purchase a CE license instead.

Important License Information:

• Please make sure you enter your email address correctly at checkout. The license(s) will be assigned to that email address.
• After purchase, you will receive a confirmation email from “PocketWizard Shop” with further instructions. Note: it may take up to 24 hours for the license(s) to be available.  If you are purchasing physical products in addition to the licenses, the licenses will not be available until the products are shipped.
• The upgrade is completed through the PocketWizard Utility via a USB connection with a computer, either a PC or Mac. It cannot be done on a smartphone or tablet.
• You will need a mini B to USB data cable for the upgrade.
• Installing E Release Firmware requires an active internet connection.
• An upgrade must be purchased for each radio and will be assigned to the radio’s serial number upon installation. Once assigned, it is non-transferable.
• E Release enabled (licensed) radios can be up/down-graded between E Release and Legacy Firmware at any time.

The post FlexTT5-Canon E Release (Receive ONLY) Firmware License (FCC-US/Canada) appeared first on PocketWizard.

With an E Release Firmware upgrade, your radios will:

• Send and receive signals with greater reliability.
• Get more than double the range of legacy firmware for remote camera(s) and/or off-camera flash(es).
• Pair your PocketWizards with the revolutionary Raven from Fusion TLC.
• Use Quad Zone Triggering available with all 32 Channels, instead of just 16.
• All use the same, single Channel system.

PLEASE READ IMPORTANT NOTES AND CHECK THE COMPATIBILITY CHART BEFORE PURCHASING E RELEASE FIRMWARE.

• When you upgrade a PocketWizard radio to the E Release, it uses a different frequency and can only communicate with other radios that have also been upgraded to the E Release.
• You will need at least 2 radios with E Release Firmware. Each radio requires its own firmware license.
• You may need to update the firmware in your Paul C Buff flash. Please check the website for details or contact us.
• This license is for an FCC frequency (North, Central, or South America) receiver.

Important License Information:

• Please make sure you enter your email address correctly at checkout. The license(s) will be assigned to that email address.
• After purchase, you will receive a confirmation email from “PocketWizard Shop” with further instructions. Note: it may take up to 24 hours for the license(s) to be available.  If you are purchasing physical products in addition to the licenses, the licenses will not be available until the products are shipped.
• The upgrade is completed through the PocketWizard Utility via a USB connection with a computer, either a PC or Mac. It cannot be done on a smartphone or tablet.
• You will need a mini B to USB data cable for the upgrade.
• Installing E Release Firmware requires an active internet connection.
• An upgrade must be purchased for each radio and will be assigned to the radio’s serial number upon installation. Once assigned, it is non-transferable.
• E Release enabled (licensed) radios can be up/down-graded between E Release and Legacy Firmware at any time.

The post PowerMC2 E Release Firmware License (FCC-US/Canada) appeared first on PocketWizard.

With an E Release Firmware upgrade, your radios will:

• Send and receive signals with greater reliability.
• Get more than double the range of legacy firmware for remote camera(s) and/or off-camera flash(es).
• Pair your PocketWizards with the revolutionary Raven from Fusion TLC.
• Use Quad Zone Triggering available with all 32 Channels, instead of just 16.
• All use the same, single Channel system.

PLEASE READ IMPORTANT NOTES BELOW AND CHECK THE
CAMERA COMPATIBILITY CHART BEFORE PURCHASING E RELEASE FIRMWARE.

• When you upgrade a PocketWizard radio to the E Release, it uses a different frequency and can only communicate with other radios that have also been upgraded to the E Release.
• You will need at least 2 radios with E Release Firmware. Each radio requires its own firmware license.
• The E Release upgrade is not available for the MiniTT1.
• If your camera is not compatible with the FlexTT5 as a transmitter, you may be able to use a Raven from Fusion TLC as a transmitter for TTL (or a Plus IIIe/Plus IV as a transmitter for manual triggering) with your FlexTT5s as receivers.
• This license is for an FCC frequency (North, Central, or South America) Transceiver. If your radio says “CE” on the label, please purchase a CE license instead.

Important License Information:

• Please make sure you enter your email address correctly at checkout. The license(s) will be assigned to that email address.
• After purchase, you will receive a confirmation email from “PocketWizard Shop” with further instructions. Note: it may take up to 24 hours for the license(s) to be available.  If you are purchasing physical products in addition to the licenses, the licenses will not be available until the products are shipped.
• The upgrade is completed through the PocketWizard Utility via a USB connection with a computer, either a PC or Mac. It cannot be done on a smartphone or tablet.
• You will need a mini B to USB data cable for the upgrade.
• Installing E Release Firmware requires an active internet connection.
• An upgrade must be purchased for each radio and will be assigned to the radio’s serial number upon installation. Once assigned, it is non-transferable.
• E Release enabled (licensed) radios can be up/down-graded between E Release and Legacy Firmware at any time.

The post FlexTT5-Nikon E Release Firmware License (FCC-US/Canada) appeared first on PocketWizard.

With an E Release Firmware upgrade, your radios will:

• Send and receive signals with greater reliability.
• Get more than double the range of legacy firmware for remote camera(s) and/or off-camera flash(es).
• Pair your PocketWizards with the revolutionary Raven from Fusion TLC.
• Use Quad Zone Triggering available with all 32 Channels, instead of just 16.
• All use the same, single Channel system.

PLEASE READ IMPORTANT NOTES BELOW BEFORE PURCHASING E RELEASE FIRMWARE.

• When you upgrade a PocketWizard radio to the E Release, it uses a different frequency and can only communicate with other radios that have also been upgraded to the E Release.
• You will need at least 2 radios with E Release Firmware. Each radio requires its own firmware license.
• This license is for an FCC frequency (North, Central, or South America) Transceiver. If your radio says “CE” on the label, please purchase a CE license instead.

Important License Information:

• Please make sure you enter your email address correctly at checkout. The license(s) will be assigned to that email address.
• After purchase, you will receive a confirmation email from “PocketWizard Shop” with further instructions. Note: it may take up to 24 hours for the license(s) to be available.  If you are purchasing physical products in addition to the licenses, the licenses will not be available until the products are shipped.
• The upgrade is completed through the PocketWizard Utility via a USB connection with a computer, either a PC or Mac. It cannot be done on a smartphone or tablet.
• You will need a mini B to USB data cable for the upgrade.
• Installing E Release Firmware requires an active internet connection.
• An upgrade must be purchased for each radio and will be assigned to the radio’s serial number upon installation. Once assigned, it is non-transferable.
• E Release enabled (licensed) radios can be up/down-graded between E Release and Legacy Firmware at any time.

The post Plus IV E Release Firmware License (FCC-US/Canada) appeared first on PocketWizard.

With an E Release Firmware upgrade, your radios will:

• Send and receive signals with greater reliability.
• Get more than double the range of legacy firmware for remote camera(s) and/or off-camera flash(es).
• Pair your PocketWizards with the revolutionary Raven from Fusion TLC.
• Use Quad Zone Triggering available with all 32 Channels, instead of just 16.
• All use the same, single Channel system.

PLEASE READ IMPORTANT NOTES BELOW BEFORE PURCHASING E RELEASE FIRMWARE.

• When you upgrade a PocketWizard radio to the E Release, it uses a different frequency and can only communicate with other radios that have also been upgraded to the E Release.
• You will need at least 2 radios with E Release Firmware. Each radio requires its own firmware license.
• This license is for an FCC frequency (North, Central, or South America) Transceiver. If your radio says “CE” on the label, please purchase a CE license instead.

Important License Information:

• Please make sure you enter your email address correctly at checkout. The license(s) will be assigned to that email address.
• After purchase, you will receive a confirmation email from “PocketWizard Shop” with further instructions. Note: it may take up to 24 hours for the license(s) to be available.  If you are purchasing physical products in addition to the licenses, the licenses will not be available until the products are shipped.
• The upgrade is completed through the PocketWizard Utility via a USB connection with a computer, either a PC or Mac. It cannot be done on a smartphone or tablet.
• You will need a mini B to USB data cable for the upgrade.
• Installing E Release Firmware requires an active internet connection.
• An upgrade must be purchased for each radio and will be assigned to the radio’s serial number upon installation. Once assigned, it is non-transferable.
• E Release enabled (licensed) radios can be up/down-graded between E Release and Legacy Firmware at any time.

The post Plus III E Release Firmware License (FCC-US/Canada) appeared first on PocketWizard.

IMPORTANT:
This is available for FCC meters only, for customers in the US and Canada. Your meter will need to be shipped to our corporate office for this upgrade.  Please contact us for information before making a purchase. This is not an upgrade that can be installed by the PocketWizard Utility.

If  you order the upgrade for the meter at the same time as upgrades for regular PocketWizard radios, your other upgrades WILL NOT be accessible immediately. You can upgrade them once the meter comes back. If you would like to upgrade the PocketWizards immediately, please order the meter upgrade separately or contact us for information before placing the order.

This is the only Sekonic meter that can be upgraded to the E Release firmware protocol at this point. The E Release upgrade can be added to both the L-478DR and the L-478DR-U versions of this meter.

The post E Release Upgrade for Sekonic L-478DR Light Meter (FCC-US/Canada) *MAIL IN ONLY* appeared first on PocketWizard.